SLíдτ2: (TRC3:SS)...P3.2...Balance & Separating...2.Beam

The Road

Chapter 3 : Solar Separating

Page 3.2 : Balance & Separating

2. Beam's Balance

The Energy's Center must has a beam and balance of the beam should be consist of this 3 things:

1. Planets's positions that orbit around, it used for locate the beam
2. Perfect road's positions, it used for find the topic 1 above
3. Beam's center

2.1 Planets's Positions That Orbit Around

Suppose that

- Sun has 3 planets orbiting around (Pic 1)

- Sun has a main path of separate line around energy's center (Pic 2).

- Each planets (A, B, C) has 6 major positions orbiting (Pic 3 is an example of planet A).

- The relationship between planets is assumed to be shown in Pic 4

And we will get a table of relationships as follows (Pic 5.1)

Example Description :

Ex1. Look at main line = L3 in red frame (Pic 5.2) means that when perfect road occurs at position A3, at the same time clashing will occurs at B1 and C4.

Ex2. Look at main line = L2, L5 in red frame (Pic 5.3) means that if a perfect road occurs at planet B, C

The direction of A is not on the separating line, but by matching with the perfect road of B and C, we will be seen the position of A (action = ellipse) on the main separate line (Pic 6)

Means that if we want to find the coordinates of the beams (determind the position by planet A), we must also have the main separate line (Pic7.1).

And in Pic 8 is shown that the position of each main separate line are matched with planet A.

2.2 Perfect Road's Positions

If all planets and Sun rotate with a counterclockwise. The position of each perfect road (A3, A6, B3, B6, C3, C6) will only occurs between the sun (inner side) and the energy's center (Pic9) (Description in the 1st & 4th of Pic 4 - Perfect Road & Moon Traveling Line)

2.3 Beam's Center

If the separate line is orbit around.....The energy's center will become a center of the beam. But the beam's link between each planet (A, B, C) may be can not use because the two ends of the beams should be in opposite directions and drawn through the energy's center.

Example in Pic 10

Pic 10 is shown the position of A, B, C resulting from each perfect road and if we drawn a beam to connected

We can get a good beam from planet A but other are bad because of B's beam and C's beam cannot pass through the energy's center.

And we can fixed this problem by use the position of planet A instead such as

1. Example's discription from Pic 8, we can drag a link from each planet A (opposite with matched) to connect a beams that come from different positions and resulting in Pic 11

Description :
The position of each A are in an opposite directions and matches as shown below :
A6, A3 (Perfect Road)
A2, A5 (Ellipse)
A1, A4 (Clashing)

2. Example's discription from Pic 3

If planet A is orbiting around the sun, and we can drag a link to shown the beam. All positions will occur in opposite directions, and Sun is the center (Pic 12)

If we cut Pic 12 into 6 segments and place it on the main path around energy's center. It will shown like in Pic 11

Brifely

Beams can occur in 2 ways:
1. Perfect road of each planets but it don't need to drag through energy's center.

2. Position of the planet that determind to used for locate the beam
(If we want to find the beam's center, we should use this way)

Character of The Beam

From Pic 5.2

If we used to calculation amount of the line with permutations and find all probability such as :

L6 * L5 * L4 = 120 line position

and if we only have 6 positions of A (A1 to A6). Therefore, each position will be matched with the 20 main line (6*20=120)

Let's say the matching example below.

A1 and L1-L20
A2 and L21-L40
A3 and L41-L60
A4 and L61-L80
A5 and L81-L100
A6 and L101-L120

And from the matched of position A and Line above....we will get a beam and swinging as shown in Pic 13 (example just 1 couple)

10/28/2020

(TRC3:SS)...P3.2...Balance & Separating...2.Beam